I think I am very close to getting my GuruPlug working again but
it fails to boot. Please help.
I followed instructions at
http://www.cyrius.com/debian/kirkwood/sheevaplug/carefully and everything went well
all the way through install debian on a 320G external usb disk.
I mounted that disk and on another system and verified that the
first linux partition has uImage and uInitrd and the second
partition has Debian. However, the GuruPlug is unable to mount
the disk and load uImage and uInitrd.
A log of the session follows. Please advise.
U-Boot 2011.03 (Apr 26 2011 - 21:35:00)
Marvell-GuruPlug
SoC: Kirkwood 88F6281_A1
DRAM: 512 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
Net: egiga0, egiga1
88E1121 Initialized on egiga0
88E1121 Initialized on egiga1
Hit any key to stop autoboot: 3 2 1 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> setenv printenv
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_console=console=ttyS0,115200
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_usb; bootm 0x00800000 0x01100000
bootcmd_usb=usb start; ext2load usb 0:1 0x0080000 /uImage; ext2load usb 0:1 0x01100000 /uInitrd
bootdelay=3
eth1addr=02:50:43:d9:87:02
ethact=egiga0
ethaddr=00:50:43:01:9B:FE
stderr=serial
stdin=serial
stdout=serial
x_bootargs=console=ttyS0,115200
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
x_bootcmd_ethernet=ping 192.168.2.1
x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000
x_bootcmd_usb=usb start
Environment size: 634/131068 bytes
Marvell>> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Marvell>> usb storage
No storage devices, perhaps not 'usb start'ed..?
Marvell>> usb treee
Device Tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
|+-2 Hub (480 Mb/s, 100mA)
USB2.0 Hub
Marvell>> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms
2: Hub, USB Revision 2.0
- USB2.0 Hub
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x05e3 Product 0x0608 Version 119.99
Configuration: 1
- Interfaces: 1 Self Powered Remote Wakeup 100mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms
Marvell>>
The external disk drive is a:
Black Western Digital My Passport Essential 320GB USB 2.0
Portable Hard Drive, OEM. Model: WDBAAA3200ABK-NESN
