Sheeva cant boot from sd card.

mhtsaras

Newbie

Karma: 0
Posts: 42

« on: June 27, 2011, 07:02:53 AM »

I've been running almost two years sheeva plug from sd card and suddenly I noticed some kernel i/o errors.
FYI I'm running Debian testing...
I booted from nand and fsck the sd card with many errors so I proceeded with fdisk and extracted a backup I had from last month to the sd card.
e2fsck says that mmcblk0p1 (kernel uimage) and mmcblk0p2(rootfs) are ok
But when i'm trying to boot from sd-card I get a "udevd[596]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev"
and after that I get stuck to the error : Waiting for /dev to be fully populated...udevd[597]: unable to receive ctrl connection: Function not implemented
udevd[597]: unable to receive ctrl connection: Function not implemented
Can someone help to resolve this or is my sd-card almost dead ?
Below is the serial console print when I try to boot from sd card (mmc).

Code:

Marvell>> boot
SDHC found. Card desciption is:
Manufacturer: 0x27, OEM "PH"
Product name: "SD08G", revision 2.0
Serial number: 2953843753
Manufacturing date: 8/2009
CRC: 0x00, b0 = 0

2821988 bytes read
## Booting image at 00800000 ...
   Image Name: Linux-2.6.32.6
   Created: 2010-01-25 20:14:12 UTC
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 2821924 Bytes = 2.7 MB
   Load Address: 00008000
   Entry Point: 00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.32.6 (kelly@speedy) (gcc version 4.4.1 (Sourcery G++ Lite er) ) #1 PREEMPT Mon Jan 25 13:14:06 MST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell SheevaPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS0,115200 rw root=/dev/mmcblk0p2 rootdelay=5
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513152KB available (5104K code, 1034K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4010, nTxLock = 32083
msgmni has been set to 1002
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3553 at 0x00001bc20000
Bad eraseblock 3554 at 0x00001bc40000
Bad eraseblock 3555 at 0x00001bc60000
Bad eraseblock 3556 at 0x00001bc80000
Bad eraseblock 3557 at 0x00001bca0000
Bad eraseblock 3558 at 0x00001bcc0000
Bad eraseblock 3559 at 0x00001bce0000
Bad eraseblock 3560 at 0x00001bd00000
Bad eraseblock 3561 at 0x00001bd20000
Bad eraseblock 3562 at 0x00001bd40000
Bad eraseblock 3563 at 0x00001bd60000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:6a:6a
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 0007
mmcblk0: mmc0:0007 SD08G 7.49 GiB
mmcblk0: p1 p2
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2011-06-26 21:51:29 UTC (1309125089)
Waiting 5sec before mounting root device...
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 179:2.
Freeing init memory: 140K

INIT: version 2.88 bootingUsing makefile-style concurrent boot in runlevel S.
.udev/ already exists on the static /dev! ... [33m(warning).[39;49m
Starting the hotplug events dispatcher: udevdudevd[596]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd[597]: unable to receive ctrl connection: Function not implemented
udevd[597]: unable to receive ctrl connection: Function not implemented
udevd[597]: unable to receive ctrl connection: Function not implemented
udevd[597]: unable to receive ctrl connection: Function not implemented
udevd[597]: unable to receive ctrl connection: Function not implemented


	Logged

spinifex

Full Member

Karma: 8
Posts: 166

Re: Sheeva cant boot from sd card.

« Reply #1 on: June 27, 2011, 04:10:41 PM »

As far as I understand Debian testing (as of a 1 week ago),

1. Boot from NAND
2. Insert SD card
3. delete /dev/.udevd from the SD
4. add the following line to /fstab
tmpfs /run tmpfs nodev,nosuid,size=100M,mode=0755 0 0
5. remove any other lines referencing udev, libinit, lock or run
6. Check the contents and doco of /etc/default/rcS and /etc/default/tmpfs

Debian now uses /run/udev


	Logged

mhtsaras

Newbie

Karma: 0
Posts: 42

Re: Sheeva cant boot from sd card.

« Reply #2 on: June 28, 2011, 01:19:17 PM »

I renamed the /dev/.udevd from the SD to /dev/.1udev-for-delete
added the following line to /fstab
tmpfs /run tmpfs nodev,nosuid,size=100M,mode=0755 0 0
Rebooted the plug but with no luck

Code:

Starting the hotplug events dispatcher: udevdudevd[589]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'

.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd[590]: unable to receive ctrl connection: Function not implemented

udevd[590]: unable to receive ctrl connection: Function not implemented

After that I created the /run directory to the sd card
and again the same bad luck...
From the http://wiki.debian.org/ReleaseGoals/RunDirectory#Packages_using_.2BAC8-dev.2BAC8..2A
it says :
/dev/.udev/, v167+ will automatically use /run/udev if /run is available and writable. (168-2 available from unstable)

and from http://wiki.debian.org/ReleaseGoals/RunDirectory#How_to_transition_from_.2BAC8-dev.2C_.2BAC8-dev.2BAC8-shm_or_.2BAC8-etc_to_.2BAC8-run.3F
says that :
All users must transition to /run for wheezy
....
1 Depend on initscripts (>= 2.88dsf-13.3)
2 Replace all usage of /dev/.* /dev/shm/.* or etc with /run
3 Move all files in /dev/.* /dev/shm/.* or etc to /run in the package postinst
...
If you need to use /run in the early initramfs, you'll need to support both /run and the existing /dev/.xxx as a fallback:

WTF?
Can we use a symlink to temporary resolve this??


« Last Edit: June 28, 2011, 01:21:27 PM by mhtsaras »	Logged

mhtsaras

Newbie

Karma: 0
Posts: 42

Re: Sheeva cant boot from sd card.

« Reply #3 on: June 28, 2011, 01:41:22 PM »

I added the following line to /etc/fstab of the sd card ...


	Logged

mhtsaras

Newbie

Karma: 0
Posts: 42

Re: Sheeva cant boot from sd card.

« Reply #4 on: July 05, 2011, 01:04:03 PM »

I extracted an old backup I had from 3/2011 and worked fine with debian wheezy.
I also rebooted 2 times and the plug was workink ok from sd card.
After that I did apt-get update with 195 updates and after that a apt-get dist upgrade.
And then after a reboot the same messages but without warnings about the new /run directory because after the updates the /run was there.
So again I couldn't boot from sd card and the boot process was stoping with the message "unable to receive ctrl connection: Function not implemented".. below is the boot proccess ...

Code:

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 3 2 1 0
SDHC found. Card desciption is:
Manufacturer: 0x1d, OEM "AD"
Product name: "SD ", revision 1.0
Serial number: 2690664377
Manufacturing date: 4/2011
CRC: 0x00, b0 = 0

2821988 bytes read
## Booting image at 00800000 ...
Image Name: Linux-2.6.32.6
Created: 2010-01-25 20:14:12 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2821924 Bytes = 2.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.32.6 (kelly@speedy) (gcc version 4.4.1 (Sourcery G++ Lite er) ) #1 PREEMPT Mon Jan 25 13:14:06 MST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell SheevaPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS0,115200 rw root=/dev/mmcblk0p2 rootdelay=5
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513152KB available (5104K code, 1034K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) Β© 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4010, nTxLock = 32083
msgmni has been set to 1002
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3553 at 0x00001bc20000
Bad eraseblock 3554 at 0x00001bc40000
Bad eraseblock 3555 at 0x00001bc60000
Bad eraseblock 3556 at 0x00001bc80000
Bad eraseblock 3557 at 0x00001bca0000
Bad eraseblock 3558 at 0x00001bcc0000
Bad eraseblock 3559 at 0x00001bce0000
Bad eraseblock 3560 at 0x00001bd00000
Bad eraseblock 3561 at 0x00001bd20000
Bad eraseblock 3562 at 0x00001bd40000
Bad eraseblock 3563 at 0x00001bd60000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:6a:6a
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address b368
mmcblk0: mmc0:b368 SD 7.51 GiB
mmcblk0: p1 p2
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2011-07-01 22:22:45 UTC (1309558965)
Waiting 5sec before mounting root device...
usb 1-1: new high speed USB device using orion-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
VFS: Mounted root (ext2 filesystem) on device 179:2.
Freeing init memory: 140K

INIT: version 2.88 booscsi 0:0:0:0: Direct-Access WD My Passport 070A 2003 PQ: 0 ANSI: 4
tingsd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 975400960 512-byte logical blocks: (499 GB/465 GiB)
scsi 0:0:0:1: CD-ROM WD Virtual CD 070A 2003 PQ: 0 ANSI: 4
scsi 0:0:0:1: Attached scsi generic sg1 type 5
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
scsi 0:0:0:2: Enclosure WD SES Device 2003 PQ: 0 ANSI: 4
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:
scsi 0:0:0:2: Attached scsi generic sg2 type 13
Using makefile-style concurrent boot in runlevel S.
.udev/ already exists on the static /dev! ... [33m(warning).[39;49m
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[62 sda17]: unable to re sda2ceive ctrl conne
ction: Function not implemented
udevd[627]: sd 0:0:0:0: [sda] Assuming drive cache: write through
unable to receivsd 0:0:0:0: [sda] Attached SCSI disk
e ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
...
...
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connesr0: scsi3-mmc drive: 51x/51x caddy
ction: Function Uniform CD-ROM driver Revision: 3.20
not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented
...
...
udevd[627]: unable to receive ctrl connection: Function not implemented
udevd[627]: unable to receive ctrl connection: Function not implemented

WTF?
The last days I had in mind to update my sd kernel because I was running a very old version 2.6.32.6
So


	Logged

mhtsaras

Newbie

Karma: 0
Posts: 42

Re: Sheeva cant boot from sd card.

« Reply #5 on: July 05, 2011, 01:19:55 PM »

@ moderators : I can't edit my message so I started a new reply to continue writing.

So I extracted again my old working backup and this time I upgraded the kernel to the latest version 2.6.39.2 and after I did the necessary apt-get updates and dist-upgrades I rebooted to check if the problem remains but this time it worked.
And until now I haven't got any problems.
I think that the problem was that the old kernel I was using was not working well with the new wheezy philosophy.


	Logged

Pages: [1]

« previous next »