• Home
  • Help
  • Search
  • Login
  • Register
Pages: [1]
Author Topic: NET: Registered protocol family 10  (Read 6130 times)
androidcoolguy
Newbie
*

Karma: 0
Posts: 13


View Profile
« on: April 26, 2011, 08:38:32 PM »

Ok, I messed up as I was trying to change Guruplug Server plus to boot from SD card but it didn't work. And I did not jot down the settings that I have for my guruplug, now it does not boot at all and stuck at "NET: Registered protocol family 10". I would like to revert back to factory defaults, booting from the usual NAND. How do I do that? Could any kind soul in this forum send me the correct uboot commands to type?

My current printenv is -

Marvell>> printenv
bootdelay=3
baudrate=115200
x_bootcmd_usb=usb start
x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000
x_bootargs=console=ttyS0,115200
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
ethact=egiga0
ethaddr=00:50:43:01:81:2c
eth1addr=00:50:43:01:81:2d
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
bootargs_root=root=/dev/mtdblock2 ro
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
cesvcid=ULULULULULULPPULULULULULDA
mainlineLinux=no
run_diag=no
stdin=serial
stdout=serial
stderr=serial

Environment size: 668/131068 bytes

And these were what I did before the hanging reboot -

Marvell>> setenv bootcmd '${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;'
Marvell>> setenv bootargs_root 'ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs'
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Erasing at 0x40000 -- 100% complete.
Writing to Nand... done
Marvell>> boot
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
       scanning bus for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
2 Storage Device(s) found

NAND read: device 0 offset 0x100000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 06400000 ...
   Image Name:   Linux-2.6.33.2-00003-g4b82fc0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2688524 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.33.2-00003-g4b82fc0 (root@msi-linux-build.marvell.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33.fa1)) #1 PREEMPT Thu Apr 22 03:29:35 PDT 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell GuruPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513536KB available (4808K code, 862K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: 00
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4014, nTxLock = 32113
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "root"
UBI: MTD device size:            507 MiB
UBI: number of good PEBs:        4056
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 4056
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 184/40
UBI: image sequence number: -1
UBI: background thread "ubi_bgt0d" started, PID 449
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:81:2c
net eth1: port 0 with MAC address 00:50:43:01:81:2d
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: guruplug:red:health
Registered led device: guruplug:green:health
Registered led device: guruplug:red:wmode
Registered led device: guruplug:green:wmode
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mmc0: new high speed SDIO card at address 0001
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2011-04-27 03:31:26 UTC (1303875086)
usb 1-1: new high speed USB device using orion-ehci and address 2
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   516225024 bytes (504126 KiB, 492 MiB, 4001 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: zlib
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:13.
Freeing init memory: 140K
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
INIT: version 2.86 booting
usb 1-1.1: new high speed USB device using orion-ehci and address 3
scsi0 : usb-storage 1-1.1:1.0
usb 1-1.3: new high speed USB device using orion-ehci and address 4
Using makefile-style concurrent boot in runlevel S.
scsi1 : usb-storage 1-1.3:1.0
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Wed Apr 27 03:31:27 UTC 2011 (warning).
Activating swap...done.
Setting the system clock.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Unable to set System Clock to: Wed Apr 27 03:31:28 UTC 2011 (warning).
Cleaning up ifupdown....
Setting up networking....
Loading kernel modules...done.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
done.
Mounting local filesystems...mount: mount point /media/usb0 does not exist
ntfs-3g: Failed to access volume '/dev/sdc1': No such file or directory

ntfs-3g 2011.1.15 integrated FUSE 27 - Third Generation NTFS Driver
                Configuration type 1, XATTRS are on, POSIX ACLS are off

Copyright (C) 2005-2007 Yura Pakhuchiy
Copyright (C) 2006-2009 Szabolcs Szakacsits
Copyright (C) 2007-2010 Jean-Pierre Andre
Copyright (C) 2009 Erik Larsson

Usage:    ntfs-3g [-o option[,...]] <device|image_file> <mount_point>

Options:  ro (read-only mount), remove_hiberfile, uid=, gid=,
          umask=, fmask=, dmask=, streams_interface=.
          Please see the details in the manual (type: man ntfs-3g).

Example: ntfs-3g /dev/sda1 /mnt/windows

Ntfs-3g news, support and information:  http://ntfs-3g.org
ntfs-3g: Failed to access volume '/dev/sdd1': No such file or directory

ntfs-3g 2011.1.15 integrated FUSE 27 - Third Generation NTFS Driver
                Configuration type 1, XATTRS are on, POSIX ACLS are off

Copyright (C) 2005-2007 Yura Pakhuchiy
Copyright (C) 2006-2009 Szabolcs Szakacsits
Copyright (C) 2007-2010 Jean-Pierre Andre
Copyright (C) 2009 Erik Larsson

Usage:    ntfs-3g [-o option[,...]] <device|image_file> <mount_point>

Options:  ro (read-only mount), remove_hiberfile, uid=, gid=,
          umask=, fmask=, dmask=, streams_interface=.
          Please see the details in the manual (type: man ntfs-3g).

Example: ntfs-3g /dev/sda1 /mnt/windows

Ntfs-3g news, support and information:  http://ntfs-3g.org
mount: mount point /media/usb3 does not exist
failed.
Activating swapfile swap...done.
Cleaning up temporary files.../lib/lsb/init-functions: line 187: /dev/null: cannot overwrite existing file
.
Configuring network interfaces...ifup: failed to open statefile /etc/network/run/ifstate: No such file or directory
failed.
Cleaning up temporary files....
fuse init (API version 7.13)
Setting kernel variables (/etc/sysctl.conf)...done.
scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9909 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:0:1: Direct-Access     Generic  STORAGE DEVICE   9909 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:1: Attached scsi generic sg1 type 0
sd 0:0:0:1: [sdb] Attached SCSI removable disk
scsi 1:0:0:0: Direct-Access     Generic  USB  SD Reader   1.00 PQ: 0 ANSI: 0 CCS
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 1:0:0:0: [sdc] 16152576 512-byte logical blocks: (8.27 GB/7.70 GiB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Assuming drive cache: write through
sd 1:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 1:0:0:0: [sdc] Assuming drive cache: write through
sd 1:0:0:0: [sdc] Attached SCSI removable disk
NET: Registered protocol family 10
Logged

pingtoo
Sr. Member
****

Karma: 15
Posts: 318


View Profile
« Reply #1 on: April 27, 2011, 06:06:16 AM »

You did a good job to preserve the system condition this make debug much easier Wink

First you need to clarify your intention, you said you want to "boot from SD", do you mean you want the rootfs load from SD or you want u-boot load kernel from SD? To me "boot from SD" mean make uboot load kernel from SD which is not happening for you base on the info you provided. however you are already load and boot from NAND as is now.

currently your setting use NAND partition 2 for rootfs and the file system is "ubifs" and you were successfully boot up but you may have mis-configured your rootfs where in its /etc/fstab it may be looking stuff from SD, your problem is because the SD is on USB which is slow to come up so it throw off the boot sequence since it can not get all the essential directories need for linux system.

If my analysis is correct then you can try to boot into single user mode by modify your "bootargs_root" append word "single". this should let you boot to shell prompt at which point you can correct your /etc/fstab and start again.

BTW, the "NET: Registered protocol family 10" is refer to IPV6, so it most likely it load the module but missing something in /etc so it stuck in there.

Good luck Smiley
Logged

Good Luck Smiley

androidcoolguy
Newbie
*

Karma: 0
Posts: 13


View Profile
« Reply #2 on: April 27, 2011, 06:31:12 AM »

Thanks for your prompt reply Smiley

>First you need to clarify your intention, you said you want to "boot from SD", do you mean you want the rootfs load from SD or you want u-boot load kernel from SD?
My rootfs was full. So I was thinking to boot my rootfs from SD, I am not interested in booting the kernel from SD (what is the benefits by the way? Shocked).

Yes, I have not change the /etc/fstab, as I am not able to get into the OS. I think if I boot using single mode, I will get the root prompt and will be able to change the fstab?
Logged

pingtoo
Sr. Member
****

Karma: 15
Posts: 318


View Profile
« Reply #3 on: April 27, 2011, 07:07:30 AM »

Once you got into single user mode you are root and can change anything you want.

I am not 100% sure I understand your situation, you said "Yes, I have not change the /etc/fstab", so if you have not change /etc/fstab than my analysis is wrong and you do not need to go into single user mode to change anything.

Anyway, if you want to use SD as your rootfs then change your "bootargs_root" to have "root=/dev/sdc[partition number where your rootfs is] rootwait". This should let you boot from SD.

Having kernel on SD allow you to upgrade kernel easier, I think you are using debian alike distro. I think it have some simple upgrade script to upgrade kernel.

Good Luck Smiley
Logged

Good Luck Smiley

androidcoolguy
Newbie
*

Karma: 0
Posts: 13


View Profile
« Reply #4 on: April 27, 2011, 02:50:53 PM »

I followed http://plugcomputer.org/plugforum/index.php?topic=1642.15 mainly -

 #fdisk /dev/sdb
   press "o"  / create a new partition table
   press "n"  / create a new partition
   press "p"  / it's a primary partition
   press "1"  / partition #1
   press enter / default first cylinder
   press enter / default last cylinder
   press "a"  / set the boot flag
   press "1" / ... for partition #1
   press "w" / save changes
   
#mkfs -t  ext3 /dev/sdb1
#mkdir /mnt/sdcard
#mount /dev/sdb1 /mnt/sdcard

2) copy files of Guruplug into microSD as:
#cp -axv / /mnt/sdcard
#cp -av /dev /mnt/sdcard
 By about two steps, the bootable microSD is available

3)  The next is how to boot the microSD,  do
#ls -l /dev/sd*
brw-rw---- 1 root floppy 8,  0 2009-08-08 16:48 /dev/sda
brw-rw---- 1 root floppy 8, 16 2009-08-08 16:48 /dev/sdb
brw-rw---- 1 root floppy 8, 17 2009-08-08 16:48 /dev/sdb1
the major and minor device numbers for /dev/sdb1′ which I put the rootfs on, are 8 and 17 respectively.
That number needs to be converted to hex, for entry in Uboot -- 8,17 in decimal converts to 8,11 in Hex,
for entry in Uboot this will be entered as 0811′.

4) Reboot the GuruPlug and this time hit any key before the system boots into Debian. Once at the Marvell prompt type:
Marvell>> nand read.e 0x6400000 0x100000 0x400000
Marvell>> setenv bootargs console=ttyS0,115200 root=0811 rootdelay=10
Marvell>> bootm 0x6400000

and I changed as you advised like the following -

nand read.e 0x6400000 0x100000 0x400000
setenv bootargs console=ttyS0,115200 root=0811 rootdelay=10
setenv bootargs_root 'root=/dev/sdb1 rootwait'
bootm 0x6400000

and I am still stuck at the last line, any idea what I should do now?

U-Boot 2010.03-01266-g42f7128-dirty (May 22 2010 - 10:37:00)
Marvell-GuruPlug

SoC:   Kirkwood 88F6281_A0
DRAM:  512 MB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0, egiga1
88E1121 Initialized on egiga0
88E1121 Initialized on egiga1
Hit any key to stop autoboot:  0
Marvell>> printenv
bootdelay=3
baudrate=115200
x_bootcmd_usb=usb start
x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000
x_bootargs=console=ttyS0,115200
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
ethact=egiga0
ethaddr=00:50:43:01:81:2c
eth1addr=00:50:43:01:81:2d
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
cesvcid=ULULULULULULPPULULULULULDA
mainlineLinux=no
run_diag=no
bootcmd=${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;
bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
stdin=serial
stdout=serial
stderr=serial

Environment size: 740/131068 bytes
Marvell>> setenv cesvcid
Marvell>> setenv mainlineLinux
Marvell>> prienv
Unknown command 'prienv' - try 'help'
Marvell>> printenv
bootdelay=3
baudrate=115200
x_bootcmd_usb=usb start
x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000
x_bootargs=console=ttyS0,115200
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
ethact=egiga0
ethaddr=00:50:43:01:81:2c
eth1addr=00:50:43:01:81:2d
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
run_diag=no
bootcmd=${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;
bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
stdin=serial
stdout=serial
stderr=serial

Environment size: 688/131068 bytes
Marvell>> n<INTERRUPT>x6400000 0x100000 0x400000
Marvell>> nand read.e 0x6400000 0x100000 0x400000

NAND read: device 0 offset 0x100000, size 0x400000
 4194304 bytes read: OK
Marvell>> setenv bootargs console=ttyS0,115200 root=0811 rootdelay=10
Marvell>> setenv bootargs_root 'root=/dev/sdb1 rootwait'
Marvell>> bootm 0x6400000
## Booting kernel from Legacy Image at 06400000 ...
   Image Name:   Linux-2.6.33.2-00003-g4b82fc0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2688524 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.33.2-00003-g4b82fc0 (root@msi-linux-build.marvell.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33.fa1)) #1 PREEMPT Thu Apr 22 03:29:35 PDT 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell GuruPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=0811 rootdelay=10
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513536KB available (4808K code, 862K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: 00
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4014, nTxLock = 32113
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:81:2c
net eth1: port 0 with MAC address 00:50:43:01:81:2d
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: guruplug:red:health
Registered led device: guruplug:green:health
Registered led device: guruplug:red:wmode
Registered led device: guruplug:green:wmode
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mmc0: new high speed SDIO card at address 0001
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2011-04-27 21:46:07 UTC (1303940767)
Waiting 10sec before mounting root device...
usb 1-1: new high speed USB device using orion-ehci and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new high speed USB device using orion-ehci and address 3
scsi0 : usb-storage 1-1.1:1.0
scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9909 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:0:1: Direct-Access     Generic  STORAGE DEVICE   9909 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:1: Attached scsi generic sg1 type 0
sd 0:0:0:1: [sdb] 7733248 512-byte logical blocks: (3.95 GB/3.68 GiB)
sd 0:0:0:1: [sdb] Write Protect is off
sd 0:0:0:1: [sdb] Assuming drive cache: write through
sd 0:0:0:1: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 0:0:0:1: [sdb] Assuming drive cache: write through
sd 0:0:0:1: [sdb] Attached SCSI removable disk

Thanks.
Logged

androidcoolguy
Newbie
*

Karma: 0
Posts: 13


View Profile
« Reply #5 on: April 27, 2011, 02:58:02 PM »

Oh well, finally it came up. I think I have removed some usb drives which are not in the USB slots anymore, going to add them back and try to reboot again. Will update again once everything is back up Smiley
Logged

Pages: [1]
Print
Jump to: