• Home
  • Help
  • Search
  • Login
  • Register
Pages: 1 [2] 3
Author Topic: 2.6.34.1 new release  (Read 11100 times)
nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #15 on: July 16, 2010, 02:20:21 AM »

Kernel successfully installed on the NAND, up and running.

However, it won't reckon my external HDD connected through esata.

fdisk -l shows no matches.

Did you load the "sata_mv" module?


Nope.
That certainly explains it all Smiley
Which file do I have to edit to make it permanent / load on boot?

Thanks!

Nuno.
Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #16 on: July 16, 2010, 10:27:06 AM »

Which file do I have to edit to make it permanent / load on boot?

Add it to /etc/modules.
Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #17 on: July 16, 2010, 06:02:45 PM »

Kernel successfully installed on the NAND, up and running.

However, it won't reckon my external HDD connected through esata.

fdisk -l shows no matches.

Did you load the "sata_mv" module?


Tried modprobe sata_mv, added it to /etc/modules as sata_mv (with and without modprobe), then rebooted the plug a couple of times. No joy.
fdisk -l returns no values.

The esata cable is tightly fastened on both ends and used to work before i had to de-brick my plug.
Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #18 on: July 16, 2010, 07:30:11 PM »

Tried modprobe sata_mv, added it to /etc/modules as sata_mv (with and without modprobe), then rebooted the plug a couple of times. No joy.
fdisk -l returns no values.

The esata cable is tightly fastened on both ends and used to work before i had to de-brick my plug.

What's the output of lsmod and dmesg?  lsmod shows which modules are loaded.  dmesg should show which devices have been found.
Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #19 on: July 17, 2010, 02:38:31 AM »

Tried modprobe sata_mv, added it to /etc/modules as sata_mv (with and without modprobe), then rebooted the plug a couple of times. No joy.
fdisk -l returns no values.

The esata cable is tightly fastened on both ends and used to work before i had to de-brick my plug.

What's the output of lsmod and dmesg?  lsmod shows which modules are loaded.  dmesg should show which devices have been found.


Here it goes:

Code:
root@ubuntu:~# modprobe sata_mv
Code:
root@ubuntu:~# lsmod
Module                  Size  Used by
sata_mv                24599  0
ipv6                  227719  10
dm_crypt               11259  0
dm_mod                 55188  1 dm_crypt
mv_cesa                 4518  0

Code:
root@ubuntu:~# dmesg
Linux version 2.6.34.1 (kelly@speedy) (gcc version 4.4.3 (Sourcery G++ Lite er) ) #4 PREEMPT Fri Jul 9 14:38:45 MDT 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell SheevaPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 131072
free_area_init_node: node 0, pgdat c05321b0, node_mem_map c05e0000
  Normal zone: 1024 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 130048 pages, LIFO batch:31
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513792k/513792k available, 10496k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xe0800000 - 0xfe800000   ( 480 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc002b000   ( 140 kB)
      .text : 0xc002b000 - 0xc04e2000   (4828 kB)
      .data : 0xc0504000 - 0xc0533520   ( 190 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
  final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 32
JFFS2 version 2.2. (NAND) 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4014, nTxLock = 32112
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 656 at 0x000005200000
Bad eraseblock 2489 at 0x000013720000
2 cmdlinepart partitions found on MTD device orion_nand
Creating 2 MTD partitions on "orion_nand":
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "rootfs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "rootfs"
UBI: MTD device size:            507 MiB
UBI: number of good PEBs:        4054
UBI: number of bad PEBs:         2
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 4054
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 10/2
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 447
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:c1:e6
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
Gating clock of unused units
before: 0x00df03dd
 after: 0x00c701d9
rtc-mv rtc-mv: setting system clock to 2010-07-17 01:00:00 UTC (1279328400)
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   515450880 bytes (503370 KiB, 491 MiB, 3995 LEBs)
UBIFS: journal size:       25804800 bytes (25200 KiB, 24 MiB, 200 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing init memory: 140K
device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
eth0: link up, 100 Mb/s, full duplex, flow control disabled
NET: Registered protocol family 10
eth0: no IPv6 routers present
Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #20 on: July 17, 2010, 11:43:43 AM »

nzimas,

What's your hardware config?  How did you reinstall the software?
Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #21 on: July 17, 2010, 01:28:29 PM »

nzimas,

What's your hardware config?  How did you reinstall the software?

To de-brick my Sheeva eSata plug (the black one), I have meticulously followed the official instructions on the Sheeva Installer wiki:
http://www.plugcomputer.org/plugwiki/index.php/SheevaPlug_Installer#How_to_install_1.0_.3F

Then I installed this new kernel using the README script, like this:
 ./README-2.6.34.1 --nandkernel

and it seems to be running:
./README-2.6.34.1 --nandkernel

The external hard drive used to work through the esata with the Ubuntu 9.04 version tweaked by NewIT (newit.co.uk).

Then i had a botched debian lenny installation attempt, my plug got bricked and I decided to reinstall everything by the book.


Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #22 on: July 17, 2010, 02:40:30 PM »

Run the following commands from the console.  If you get "no device found", then I'd say it's a problem with the u-boot that's installed.  Not all u-boot versions can detect the sata controller.

Marvell>> version

U-Boot 1.1.4 (Dec 27 2009 - 22:03:21) Marvell version: 3.4.27 - pingtoo patch.01
Marvell>> ide reset

Reset IDE:
Marvell Serial ATA Adapter
Warning Integrated SATA is Powered Off
no device found
Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #23 on: July 17, 2010, 03:33:17 PM »

nzimas,

Looks like you're going to need to install the u-boot from new-it.

Here's a link:

http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html
Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #24 on: July 17, 2010, 06:29:05 PM »

@cbxbiker61

Thanks for all your help.
Not yet there, though.

The newit u-boot version has been successfully loaded, but i still don't see the esata hard drive.

Here's a full boot log:
Code:
U-Boot 1.1.4 (Jul 14 2009 - 06:46:57) Marvell version: 3.4.16

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF120

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.34.1
   Created:      2010-07-09  20:38:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2742036 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.34.1 (kelly@speedy) (gcc version 4.4.3 (Sourcery G++ Lite er) ) #4 PREEMPT Fri Jul 9 14:38:45 MDT 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell SheevaPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513792k/513792k available, 10496k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xe0800000 - 0xfe800000   ( 480 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc002b000   ( 140 kB)
      .text : 0xc002b000 - 0xc04e2000   (4828 kB)
      .data : 0xc0504000 - 0xc0533520   ( 190 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) � 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4014, nTxLock = 32112
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 656 at 0x000005200000
Bad eraseblock 2489 at 0x000013720000
2 cmdlinepart partitions found on MTD device orion_nand
Creating 2 MTD partitions on "orion_nand":
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "rootfs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "rootfs"
UBI: MTD device size:            507 MiB
UBI: number of good PEBs:        4054
UBI: number of bad PEBs:         2
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 4054
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 10/2
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 447
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:c1:e6
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2010-07-18 01:18:40 UTC (1279415920)
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   515450880 bytes (503370 KiB, 491 MiB, 3995 LEBs)
UBIFS: journal size:       25804800 bytes (25200 KiB, 24 MiB, 200 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing init memory: 140K
 * Filesystem type 'fusectl' is not supported. Skipping mount.
[ OK ]ting preliminary keymap...       
[ OK ]rting kernel event manager...       
[ OK ]ding hardware drivers...       
[ OK ]ding kernel modules...         * Loading manual drivers...       
[ OK ]ting kernel variables (/etc/sysctl.conf)...       
[ OK ]ting kernel variables (/etc/sysctl.d/10-console-messages.conf)...       
[ OK ]ting kernel variables (/etc/sysctl.d/10-network-security.conf)...       
[ OK ]ivating swap...       
[ OK ]rting early crypto disks...       
[ OK ]rting remaining crypto disks...       
 * Checking file systems...        fsck 1.41.4 (27-Jan-2009)
[ OK ]
[ OK ]nting local filesystems...       
[ OK ]ivating swapfile swap...       
[ OK ]figuring network interfaces...       
[ OK ]ting up console font and keymap...       
[ OK ]rting system log daemon...       
[ OK ] * Starting kernel log daemon...       

Ubuntu 9.04 ubuntu ttyS0

[ OK ] login:  * Starting OpenBSD Secure Shell server sshd       
[ OK ] * Starting periodic command scheduler crond       
       * Restarting OpenBSD Secure Shell server sshd
Logged

cjm
Jr. Member
**

Karma: 6
Posts: 69


View Profile
« Reply #25 on: July 18, 2010, 02:18:53 AM »

I couldn't see any messages around sata_mv in any of the logs. What happens when you type "rmmod sata_mv", then "modprobe sata_mv", then "dmesg"? Do you get any messages from sata_mv at all?

BTW, the new kernels have official support for eSATA plugs but they use a different acrNumber for this. The original plug uses 2097 as arcNumber, the eSATA plug uses 2678. You will have to set the arcNumber in uboot to 2678 to get eSATA working with the official kernels.

Thanks,
--Christian
Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #26 on: July 18, 2010, 05:38:40 AM »

rmmod and modprobre correctly remove and load the module, but demesg remains silent on sata devices:
Code:
root@ubuntu:~# dmesg | grep sata
root@ubuntu:~#

Perhaps the key to solve this lies in the acrNumber.

How exactly can I change the value?

Thanks.

Nuno.

[EDIT]

Will try setenv arcNumber 2678
Hope it replaeces 2097 and not merelyn add another arcNumber.
« Last Edit: July 18, 2010, 05:46:27 AM by nzimas » Logged

nzimas
Newbie
*

Karma: 0
Posts: 8


View Profile
« Reply #27 on: July 18, 2010, 11:06:24 AM »

Now we're talking Smiley

setenv arcNumber 2678
savenv
reset

did the trick.

Thanks a lot, Christian!
Logged

jrod
Newbie
*

Karma: 0
Posts: 2


View Profile
« Reply #28 on: July 19, 2010, 06:47:39 AM »

I'm wondering if I might make another request, I'm trying to set up a somewhat complex routing setup and have found that not having multiple routing tables available is making it quite difficult:

Code:
# CONFIG_IP_MULTIPLE_TABLES is not set

Can this be enabled in future kernels? Smiley
Logged

cbxbiker61
Global Moderator
Sr. Member
*****

Karma: 38
Posts: 497


View Profile
« Reply #29 on: July 20, 2010, 02:27:27 PM »

I'm wondering if I might make another request, I'm trying to set up a somewhat complex routing setup and have found that not having multiple routing tables available is making it quite difficult:

Code:
# CONFIG_IP_MULTIPLE_TABLES is not set

Can this be enabled in future kernels? Smiley

I've just updated 2.6.34.1 to include this.
Logged

Pages: 1 [2] 3
Print
Jump to: