• Home
  • Help
  • Search
  • Login
  • Register
Pages: [1]
Author Topic: Guruplug does not recognize USB devices  (Read 2324 times)
sbe
Newbie
*

Karma: 0
Posts: 2


View Profile
« on: June 15, 2010, 11:07:28 PM »

Hi!

Until yesterday my Guruplug+ was running fine with a miniSD card and an active, external USB HUB. A usb-2-serial converter, a harddisk and a usb stick were connected to this external hub without any problems.
Then I did a apt-get update and upgrade because I want to install etherwake package. This worked fine as well.

But after a reboot the plug does not recognize the miniSD card nor the devicey on the external hub. Networking is still ok. The dmesg output will follow. At the moment I do not have an idea whats going wrong, I have the suspicion that the apt-get upgrade installed some new packages to my plug, that do not fit very well.

lsusb shows only one entry instead of several:
Code:
root@sbeplug:~# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


Do you have any idea what's going wrong here or what I can check?

regards,
stefan

Code:
Linux version 2.6.32-00007-g56678ec (root@msi-linux-build.marvell.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33.fa1)) #1 PREEMPT Mon Feb 8 03:49:55 PST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell Plug2L Reference Board
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 131072
free_area_init_node: node 0, pgdat c05881c8, node_mem_map c065f000
  Normal zone: 1024 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 130048 pages, LIFO batch:31
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513024KB available (5144K code, 1034K data, 148K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Cache support initialised.
initial MPP regs: 01111111 11113311 33331111 33333333 00003333 00000222 00000000
  final MPP regs: 01111111 11113311 33331111 33333333 00003333 00000222 00000000
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4010, nTxLock = 32080
msgmni has been set to 1002
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 1
scsi0 : sata_mv
ata1: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
ata1: SATA link down (SStatus 0 SControl F300)
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "root"
UBI: MTD device size:            507 MiB
UBI: number of good PEBs:        4056
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 4056
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 9/1
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 454
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:85:04
net eth1: port 0 with MAC address 00:50:43:01:85:05
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug2l:red:health
Registered led device: plug2l:green:health
Registered led device: plug2l:red:wmode
Registered led device: plug2l:green:wmode
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mmc0: new high speed SDIO card at address 0001
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
Gating clock of unused units
before: 0x00dfc3fd
 after: 0x00cf41d9
rtc-mv rtc-mv: setting system clock to 2010-06-16 03:59:58 UTC (1276660798)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   516225024 bytes (504126 KiB, 492 MiB, 4001 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: zlib
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:13.
Freeing init memory: 148K
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
libertas_sdio mmc0:0001:1: firmware: requesting sd8688_helper.bin
libertas: can't load helper firmware
libertas: failed to load helper firmware
libertas_sdio: probe of mmc0:0001:1 failed with error -2
Bluetooth: vendor=0x2df, device=0x9105, class=255, fn=2
btmrvl_sdio mmc0:0001:2: firmware: requesting sd8688_helper.bin
btmrvl_sdio_download_helper: request_firmware(helper) failed, error code = -2
btmrvl_sdio_download_fw: Failed to download helper!
btmrvl_sdio_probe: Downloading firmware failed!
eth0: link up, 100 Mb/s, full duplex, flow control disabled
NET: Registered protocol family 10
eth0: no IPv6 routers present
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (8022 buckets, 32088 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
« Last Edit: June 15, 2010, 11:46:36 PM by sbe » Logged

trampjuice
Newbie
*

Karma: 0
Posts: 14


View Profile
« Reply #1 on: August 30, 2010, 02:47:29 PM »

Exactly same problem but i have a sheevaplug.
I had everything working fine - many devices detected on my belkin usb hub no problem, yet while messing around with setenv in UBOOT I did a resetenv by accident and lost all my UBOOT settings. I reconstructed enough to make the plug boot OK from the guide on this site, but now I get the same error message as you.
I also installed a few massive packages on the plug with aptitude.
I have only rebooted 3 times to try to correct this so it may be that the usb start etc.. in UBOOT is the issue here in that its notoroius for not detecting USB devices, or it may be missing a UBOOT enviromental setting

Logged

trampjuice
Newbie
*

Karma: 0
Posts: 14


View Profile
« Reply #2 on: August 31, 2010, 12:15:31 AM »

My Usb hub - belkin F5U404 (powered).
This hub, which was working - been right through UBOOT enviromental settings, setting them back to what they should be.

But still no luck in enumerating devices on the usb via

Marvell >> usb start, usb reset, usb tree no matter how many times i do it.

If I plug in my WD MyBook HDD and remove the hub, its detected.

Obviously there is no operating system at this level which removes any possibility of aptitude conflicts etc...

Its either the hubs faulty or the sheevaplug is.



Logged

trampjuice
Newbie
*

Karma: 0
Posts: 14


View Profile
« Reply #3 on: August 31, 2010, 12:39:06 AM »

Well well well - the brand new Belkin hub bought from Tesco is the culprit. Lasted all of 1 day working. Tested it on my other computer and still nothing.
Luckly, the sheevaplug is fine.
Logged

feffer
Jr. Member
**

Karma: -1
Posts: 56


View Profile
« Reply #4 on: September 06, 2010, 03:15:51 PM »

I'm assuming you have either labeled your USB devices in /etc/fstab or used their UUIDs. Leaving them as /dev/sda1, /dev/sda2 etc can lead to problems on rebooting, since they may remount in a different order -- which can happen on a hub. Maybe not your problem, but it doesn't hurt to do this.

I think the best way to upgrade Debian (assuming that's what you're running) is to do:
Code:
#apt-get update && apt-get dist-upgrade
Then check to see what apt will do before saying "yes." Does it want to remove a bunch of things? That may be a bad idea; better hold off. On the other hand, if it looks clean, the upgrade should go well. If you think you've already had an upgrade or package conflict, try:
Code:
#apt-get install -f
Then apt will either "fix" dependency problems or report errors.

I use this process on my sidux (debian sid) machines, and it works well. It's also been working fine on the SheevaPlug running Lenny. On the other hand, Ubuntu might be different even though it's Debian based. If anyone knows more exactly about this, please comment.

Logged

Pages: [1]
Print
Jump to: