U-Boot upgrade via USB, How?

Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

# php runme.php nand

**** exec(modprobe ftdi_sio vendor=0x9e88 product=0x9e8f)
**** Preparing environment variables file ...
reading uboot/uboot-env/uboot-dflt.txt
uboot/uboot-env/fw_setenv baudrate 115200
CRC read error on uboot-env.bin: Success
uboot/uboot-env/fw_setenv loads_echo 0
uboot/uboot-env/fw_setenv ipaddr 10.4.50.165
uboot/uboot-env/fw_setenv serverip 10.4.50.5
uboot/uboot-env/fw_setenv rootpath /mnt/ARM_FS/
uboot/uboot-env/fw_setenv netmask 255.255.255.0
uboot/uboot-env/fw_setenv stdin serial
uboot/uboot-env/fw_setenv stdout serial
uboot/uboot-env/fw_setenv stderr serial
uboot/uboot-env/fw_setenv console console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0$uboot$ro,0x1ff00000@0x100000$root$
uboot/uboot-env/fw_setenv mainlineLinux no
uboot/uboot-env/fw_setenv CASset min
uboot/uboot-env/fw_setenv enaMonExt no
uboot/uboot-env/fw_setenv enaCpuStream no
uboot/uboot-env/fw_setenv enaWrAllo no
uboot/uboot-env/fw_setenv pexMode RC
uboot/uboot-env/fw_setenv disL2Cache no
uboot/uboot-env/fw_setenv setL2CacheWT yes
uboot/uboot-env/fw_setenv disL2Prefetch yes
uboot/uboot-env/fw_setenv enaICPref yes
uboot/uboot-env/fw_setenv enaDCPref yes
uboot/uboot-env/fw_setenv sata_dma_mode yes
uboot/uboot-env/fw_setenv MALLOC_len 1
uboot/uboot-env/fw_setenv ethprime egiga0
uboot/uboot-env/fw_setenv netbsd_en no
uboot/uboot-env/fw_setenv vxworks_en no
uboot/uboot-env/fw_setenv bootargs_root root=/dev/nfs rw
uboot/uboot-env/fw_setenv bootargs_end :::DB88FXX81:eth0:none
uboot/uboot-env/fw_setenv image_name uImage
uboot/uboot-env/fw_setenv bootcmd tftpboot 0x2000000 \$$image_name$\;setenv bootargs \$$console$ \$$bootargs_root$ nfsroot=\$$serverip$:\$$rootpath$ ip=\$$ipaddr$:\$$serverip$\$$bootargs_end$ \$$mvNetConfig$ \$$mvPhoneConfig$\; bootm 0x2000000\;
uboot/uboot-env/fw_setenv standalone fsload 0x2000000 \$$image_name$\;setenv bootargs \$$console$ root=/dev/mtdblock0 rw ip=\$$ipaddr$:\$$serverip$\$$bootargs_end$ \$$mvPhoneConfig$\; bootm 0x2000000\;
uboot/uboot-env/fw_setenv bootdelay 3
uboot/uboot-env/fw_setenv disaMvPnp no
uboot/uboot-env/fw_setenv ethaddr 00:50:43:4e:2a:14
uboot/uboot-env/fw_setenv ethmtu 1500
uboot/uboot-env/fw_setenv mvPhoneConfig mv_phone_config=dev0:fxs,dev1:fxs
uboot/uboot-env/fw_setenv mvNetConfig mv_net_config=$00:11:88:0f:62:81,0:1:2:3$,mtu=1500
uboot/uboot-env/fw_setenv usb0Mode host
uboot/uboot-env/fw_setenv yuk_ethaddr 00:00:00:EE:51:81
uboot/uboot-env/fw_setenv nandEcc 1bit
uboot/uboot-env/fw_setenv netretry no
uboot/uboot-env/fw_setenv rcvrip 169.254.100.100
uboot/uboot-env/fw_setenv loadaddr 0x02000000
uboot/uboot-env/fw_setenv autoload no
uboot/uboot-env/fw_setenv enaAutoRecovery yes
uboot/uboot-env/fw_setenv ethact egiga0
reading uboot/uboot-env/uboot-nand-custom.txt
uboot/uboot-env/fw_setenv bootargs_root ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
uboot/uboot-env/fw_setenv mtdpartitions mtdparts=orion_nand:0x400000@0x100000$uImage$,0x1fb00000@0x500000$rootfs$
uboot/uboot-env/fw_setenv ethaddr 00:50:43:01:4d:81
uboot/uboot-env/fw_setenv real_bootcmd setenv bootargs \$$bootargs_console$ \$$mtdpartitions$ \$$bootargs_root$\; nand read.e 0x00800000 0x00100000 0x00400000\; bootm 0x00800000
uboot/uboot-env/fw_setenv bootargs_console console=ttyS0,115200
uboot/uboot-env/fw_setenv bootcmd run recover1
uboot/uboot-env/fw_setenv recover1 setenv mainlineLinux yes\; setenv arcNumber 2097\; setenv bootcmd run recover2\; saveenv\; reset
uboot/uboot-env/fw_setenv recover2 run recover3\; setenv bootcmd \$$real_bootcmd$\; saveenv\; setenv bootargs \$$bootargs_console$ \$$mtdpartitions$ root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand\; bootm 0x00800000 0x01100000
uboot/uboot-env/fw_setenv recover3 run recover4\; nand erase clean 0x00100000 0x00400000\; nand write.e 0x00800000 0x00100000 0x00400000
uboot/uboot-env/fw_setenv recover4 usb start\; fatload usb 0 0x00800000 uImage\; fatload usb 0 0x01100000 initrd

**** Burning uboot and environment variables ... This will take few minutes ...
Open On-Chip Debugger 0.2.0 (2009-07-26-14:56) Release
$URL: http://svn.berlios.de/svnroot/repos/openocd/tags/openocd-0.2.0/src/openocd.c $
For bug reports, read http://svn.berlios.de/svnroot/repos/openocd/trunk/BUGS
2000 kHz
jtag_nsrst_delay: 200
jtag_ntrst_delay: 200
dcc downloads are enabled
Info : JTAG tap: feroceon.cpu tap/device found: 0x20a023d3 (mfg: 0x1e9, part: 0x0a02, ver: 0x2)
Info : JTAG Tap/device matched
target state: halted
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x000000d3 pc: 0xffff0000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
0 0 1 0: 00052078
NAND flash device 'NAND 512MiB 3,3V 8-bit' found
successfully erased blocks 5 to 6 on NAND flash device 'NAND 512MiB 3,3V 8-bit'
wrote file uboot-env.bin to NAND flash 0 up to offset 0x000c0000 in 39.231319s
target state: halted
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x000000d3 pc: 0xffff0000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
0 0 1 0: 00052078
NAND flash device 'NAND 512MiB 3,3V 8-bit' found
successfully erased blocks 0 to 4 on NAND flash device 'NAND 512MiB 3,3V 8-bit'
wrote file uboot.bin to NAND flash 0 up to offset 0x00074000 in 143.178391s

**** U-boot should be up and running now. Open your console ...

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Dec 23 2009 - 13:32:43) Marvell version: 3.4.27

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Dec 23 2009 - 13:32:43) Marvell version: 3.4.27

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices...
USB device not responding, giving up (status=20)
2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **

NAND erase: device 0 offset 0x100000, size 0x400000
Erasing at 0x4e0000 -- 100% complete. Cleanmarker written at 0x4e0000.
OK

NAND write: device 0 offset 0x100000, size 0x400000

Writing data at 0x4ff800 -- 100% complete.
4194304 bytes written: OK
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>