• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: 1 2 [3] 4 5 ... 19
31  General Category / General Discussion / Re: Dead Sheeva? on: June 23, 2010, 04:35:20 AM
use a voltmeter.
32  Linux Stuff / General Linux questions / Re: [resolved] Tomato/DD-WRT type package for Debian? on: June 23, 2010, 12:02:44 AM
port 1900 and 49152 (and up, if you did not nail it in the mediatomb config)
33  General Category / General Discussion / Re: Guruplug Chmod uns /media/usb0 failed on: June 21, 2010, 04:23:14 AM
if the sd card is essential to run system services, then it should be mounted via /etc/fstab
34  Hardware and U-Boot firmware / Hardware / Re: Wanted to buy -- Sheevaplug V 1.3 pcb from Sheevaplug with dead power supply on: June 21, 2010, 04:21:33 AM
if you bought from globalscales USA, they are not bound by UK (or EU) laws. They state a 30day warranty.

if you bought as an end user from a EU Reseller, you have a two year warranty and need to contact your reseller.
35  General Category / General Discussion / Re: Guruplug Chmod uns /media/usb0 failed on: June 21, 2010, 02:39:23 AM
the permissions are stored in the mounted filesystem -> on the sd card. As the sd card is formatted as vfat it knows nothing about permissions. You need to specify the permissions in the mount. See "man mount". The options you are interested are fmask, dmask, uid, gid
36  General Category / General Discussion / Re: SD root filesystem flies! on: June 21, 2010, 12:05:44 AM
Code:
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
your bootargs_root points to an ubi partition living in nand. If you want to boot from your sdcard you need to add mmcinit to your bootcmd and change bootargs_root. Details should be easy to find in this forum.
37  General Category / General Discussion / Re: Dead Sheeva? on: June 18, 2010, 02:11:57 PM
same answer as hundred times before...

get an external 5V/3A powersupply (or 2A if you can't find it. Or a powered USB Hub with at least four ports and steal the PSU). Take the plug apart (screws below the rubber feets). Take care that the internal PSU has high voltage capacitors that can be nasty hours after unplugging. Remove internal PSU, drill a hole into the case, run the wire of your new external PSU inside, solder. done.
38  General Category / General Discussion / Re: Dead Sheeva? on: June 18, 2010, 12:20:15 PM
symptoms of a fried powersupply.

39  Hardware and U-Boot firmware / Hardware / Re: GuruPlug Server Plus Heat Problems on: June 17, 2010, 06:06:11 AM
a sink of this size should be capable to transport the 10W of the plug by convection and not require a fan. Would you mind trying?
40  General Category / General Discussion / Re: Compiler settings affect floating point performance? on: June 16, 2010, 10:09:31 AM
i assume that the libc ist multiarch and catches missing FPU and does automaticly switch to softfloat.
41  General Category / General Discussion / Re: Compiler settings affect floating point performance? on: June 16, 2010, 12:34:48 AM
there is no hardware floating point unit on the sheevaplug.
42  Linux Stuff / Kernel / Re: How to use headers from sheeva.with-linux.com on: June 15, 2010, 02:18:30 PM
if just want the headers untar them so that in the end you find them in /usr/include/linux on the plug.

43  Linux Stuff / Kernel / Re: How to use headers from sheeva.with-linux.com on: June 15, 2010, 08:12:50 AM
depends how clean your drivers source tarball is. Something along these lines
Code:
export BASE=/tmp/foobar
export PATH=/path/to/cross/compilers/bin:$PATH
mkdir -p $BASE/sysroot
cd $BASE/sysroot
tar zxvf sheeva_linux_header.tar.gz
cd $BASE
tar zxvf some_drivers_tarball.tar.gz
cd $BASE/some_driver
./configure --target=arm-elf --with-headers=$SYSROOT/usr/include --with-sysroot=$SYSROOT
make
44  General Category / General Discussion / Re: *** Warning - bad CRC or NAND, using default environment on: June 14, 2010, 11:52:32 PM
u-boot is fine. Interrupt the boot (hit anything to reach the marvell prompt). set your ethernet address(es) (set ethaddr aa:bb:cc:...). Save environment (saveenv) and your are done.

45  General Category / General Discussion / Re: sheevaplug as printserver on: June 14, 2010, 08:38:49 AM
you can try to install the ppd from http://www.openprinting.org/printer/Brother/Brother-HL-2030
Pages: 1 2 [3] 4 5 ... 19