Latest posts of: peterpan

Show Posts
Pages: [1]

1	Hardware and U-Boot firmware / Hardware / usb connect-debounce failed, port 1 disabled	on: May 24, 2009, 12:34:05 PM
Hi, one of my usb sticks won't work, when I plug them directly into the sheeva plug. The stick works however, when I put a powered usb hub inbetween. At uboot, it's just not recognized; when linux (2.6.30rc6) is running, it periodically outputs: `hub 1-0:1.0: connect-debounce failed, port 1 disabled` Also strange is, that I cannot use the hub without power supply with the sheeva at all. I thought, that it may have something to do with the amount of power, that is drawn via usb, but the Toshiba stick that works reports a higher maximum power consumption than the Transcend stick and the Genesys hub that don't work. I also tested this without the console cable connected. Does anybody have an idea regarding this problem? Thanks, Peter Here is the lsusb output for the three devices: Code: Bus 001 Device 028: ID 1307:0165 Transcend Information, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1307 Transcend Information, Inc. idProduct 0x0165 bcdDevice 1.00 iManufacturer 1 iProduct 2 iSerial 3 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 39 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 98mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 8 Bus 001 Device 027: ID 0930:6529 Toshiba Corp. TravelDrive Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0930 Toshiba Corp. idProduct 0x6529 TravelDrive bcdDevice 1.00 iManufacturer 1 iProduct 2 iSerial 3 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 39 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 200mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 4 Bus 001 Device 026: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x05e3 Genesys Logic, Inc. idProduct 0x0608 USB-2.0 4-Port HUB bcdDevice 7.02 iManufacturer 0 iProduct 1 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0001 1x 1 bytes bInterval 1

2	General Category / General Discussion / Re: Sheevaplug installer - alpha-5 release - Testers needed	on: May 24, 2009, 11:57:09 AM
Quote from: Rabeeh Khoury on May 24, 2009, 09:01:57 AM Anyhow, I fixed the script (attached initrd, please replace the one you are using), please try it with the non-working USB stick. Yes, this works! Very good. I tried it with both sticks, just to be sure.

3	General Category / General Discussion / Re: Sheevaplug installer - alpha-5 release - Testers needed	on: May 24, 2009, 08:41:49 AM
It works! I tried a different usb stick, that does work with uboot without putting a powered hub inbetween. And that worked. The contents (the files from the installer directory) and partition type (W95 FAT32 LBA) are exactly the same. I don't really know what the difference is . The alternative stick was 512mb while the former was 4gb, but this can't be it. Quote from: Rabeeh Khoury on May 23, 2009, 05:27:44 AM The first one seems to be ok since there is no /dev/sda1, but only /dev/sda (no partitions on the USB stick). Are you sure that there are no partitions on the USB stick? I tried to make a USB stick without partition table, but uboot seems to need one. While installing it now says: `mount: mounting /dev/sda on /mnt1 failed: Invalid argument` instead of: `mount: mounting /dev/sda1 on /mnt1 failed: Device or resource busy` Thanks for your help. If you are interested in more information regarding my sticks or if I can try something for you, let me know.

4	General Category / General Discussion / Re: Sheevaplug installer - alpha-5 release - Testers needed	on: May 22, 2009, 03:08:15 PM
ok, it seems that uboot on my plug will only talk to my usb-stick if i put a powered usb hub inbetween and plug it all in before booting. Now I see that installation copies and flashes the files, but now there is another error: Code: ubiformat: formatting eraseblock 4054 -- 99 % complete ubiformat: formatting eraseblock 4055 -- 100 % complete UBI: attached mtd1 to ubi0 UBI: MTD device name: "rootfs" UBI: MTD device size: 507 MiB UBI: number of good PEBs: 4040 UBI: number of bad PEBs: 16 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 3996 UBI: total number of reserved PEBs: 44 UBI: number of PEBs reserved for bad PEB handling: 40 UBI: max/mean erase counter: 4/1 UBI: background thread "ubi_bgt0d" started, PID 556 UBI device number 0, total 4040 LEBs (521256960 bytes, 497.1 MiB), available 3996 LEBs (515579904 bytes, 491.7 MiB), LEB size 129024 bytes (126.0 KiB) Set volume size to 515579904 Volume ID 0, size 3996 LEBs (515579904 bytes, 491.7 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs", alignment 1 ** Mounting root filesystems mount: mounting /dev/sda1 on /mnt1 failed: Device or resource busy UBIFS: default file-system created UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 513644544 bytes (501606 KiB, 489 MiB, 3981 LEBs) UBIFS: journal size: 25675776 bytes (25074 KiB, 24 MiB, 199 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 4952683 bytes (4836 KiB) **** ERROR - no rootfs.tar.gz file found on USB stick UBIFS: un-mount UBI device 0, volume 0 The system is going down NOW! [.....] usb 1-1: new high speed USB device using orion-ehci and address 2 Warning: unable to open an initial console. Kernel panic - not syncing: No init found. Try passing init= option to kernel. [<c00309c0>] (unwind_backtrace+0x0/0xe0) from [<c003db20>] (panic+0x50/0x120) [<c003db20>] (panic+0x50/0x120) from [<c002b53c>] (init_post+0xd4/0xfc) [<c002b53c>] (init_post+0xd4/0xfc) from [<c0008738>] (kernel_init+0xc4/0xec) [<c0008738>] (kernel_init+0xc4/0xec) from [<c0040b18>] (do_exit+0x0/0x6ac) I attached the complete log of this command line ( sudo ./runme.sh ; cu --nostop -s 115200 --line /dev/ttyUSB1 ) 2>&1 \| tee install.log

5	General Category / General Discussion / Re: Sheevaplug installer - alpha-5 release - Testers needed	on: May 22, 2009, 12:11:30 PM
While looking around, it seemed to me, that usb does not work at all: Code: Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Marvell>> fatload usb 0 0x00200000 uImage Can't read from device 0 Unable to use usb 0:1 for fatload

6	General Category / General Discussion / Re: Sheevaplug installer - alpha-5 release - Testers needed	on: May 22, 2009, 11:34:52 AM
Hi, here are my first-time experiences with the installer: I formattet a USB-Stick and copied the files from the installer directory. Connected the Terminal-Cable and USB-Stick and turned on the Plug. I started "sudo ./runme.sh" and everything went fine. After opening the console as advised, there was lots of stuff going on including erasing and writing until it ended with: Code: ... Writing data at 0x4f5800 -- 99% complete. Writing data at 0x4ff800 -- 100% complete. 4194304 bytes written: OK Saving Environment to NAND... Erasing Nand...Writing to Nand... done ## Booting image at 00200000 ... Bad Magic Number Marvell>> What can I do to boot the new system? I have attached my current environment, but let me know if you need more info. Thanks, Peter Code: baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs mtdpartitions=mtdparts=orion_nand:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ethaddr=00:62:81:a0:00:00 real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00200000 0x00100000 0x003ff000; bootm 0x00200000 bootargs_console=console=ttyS0,115200 recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions); bootm 0x00200000 0x01100000 recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00200000 0x00100000 0x00400000 recover4=usb start; fatload usb 0 0x00200000 uImage; fatload usb 0 0x01100000 initrd arcNumber=2097 stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00200000 0x00100000 0x003ff000; bootm 0x00200000 bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)

Pages: [1]