• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: [1]
1  Hardware and U-Boot firmware / U-Boot stuff / SD card / u-boot problems on: May 16, 2012, 02:52:59 PM
Hello,

I am quite new to this............................

I am trying to install debian (squeeze) to an SD card on the sheevaplug

u-boot 3.4.27 was installed and i upgraded it to  the DENX variant  via my tftp

(http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html)

Everything went ok, but now the ESIA installer does not sse ANY SD card anymore when installing ( if i install to NAND, i can later mount it )

Am i missing something ?

Can i dowgrade t0 3.4.27 ( Marvell) wehere can find that u-boot image ?

Thanx for any help ,

Poekel





2  Hardware and U-Boot firmware / Hardware / Newbie / messed up sheevaplug on: May 24, 2010, 01:08:04 PM
Hello,

I am a newbie to the sheevaplug  and already messed  it iup installing debian.

Can i somehow go back to the initial settings ?  ( ubuntu ?)

The problem is  that boot the linux kernel is hangs

I have seen bad block error from nand  / Can i resolve this ?


HELP APPRECIATED!

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> tftpboot 0x01100000 uInitrd
Using egiga0 device
TFTP from server 192.168.2.12; our IP address is 192.168.2.33
Filename 'uInitrd'.
Load address: 0x1100000
Loading: #################################################################
   #################################################################
   #################################################################
   #################################################################
   #################################################################
   #################################################################
   #################################################################
   #################################################################
   ###############
done
Bytes transferred = 2735033 (29bbb9 hex)
Marvell>> tftpboot 0x00800000 uImage
Using egiga0 device
TFTP from server 192.168.2.12; our IP address is 192.168.2.33
Filename 'uImage'.
Load address: 0x800000
Loading: #################################################################
   #################################################################
   #################################################################
   #################################################################
   #################################################################
   #############################
done
Bytes transferred = 1811960 (1ba5f8 hex)
Marvell>> setenv bootargs console=ttyS0,115200 base-installer/initramfs-tools/driver-policy=most mirror/suite=stable apt-setup/local0/repository="http://people.debian.org/~tbm/orion lenny main" apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F
Marvell>> bootm 0x00800000 0x01100000
## Booting image at 00800000 ...
   Image Name:   Debian kernel
   Created:      2010-02-12   1:37:09 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1811896 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   debian-installer ramdisk
   Created:      2010-03-30  15:57:01 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    2734969 Bytes =  2.6 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.




Pages: [1]