• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: 1 ... 3 4 [5] 6 7 ... 9
61  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 27, 2011, 07:16:28 AM
I have the same issue sometime and am working on it

sometime unplugging the plug (from the main power) and reconnect helps
62  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 26, 2011, 03:27:11 PM
Agreed I struggle a lot as well but then I learn a lot eventually

I had so much "problems" that now I am no longer afraid of bricking my plug. I am fairly certain I can recover it now Smiley

flipflip is a familiar of this forum so i would say the best is to contact and expose the issue you had.

but ultimately no one is paying him to help anyone  Wink
63  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 26, 2011, 07:28:48 AM
Hi

I will look into writing a clearer explanation but regarding the kwb uboot and the missing beginning...I have the same but it works

interrupt the boot and once in the uboot prompt type version

you will see that which uboot you use. It will be flipflip's one!
64  Linux Stuff / Linux distributions / Re: Upgraded Kernel will not boot. on: February 25, 2011, 12:01:21 PM
is there a way to know what kernel is supported by a specific uboot?

I am asking because I installed the uboot from http://oinkzwurgl.org/guruplug_uboot and then install Debian on a microSD card and i end in the same state:

a kernel panic

The kernel I boot is Linux version 2.6.32-5-kirkwood (Debian 2.6.32-30)

thanks
65  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 23, 2011, 01:41:29 PM
Hum!

I thought that this part of updating the uboot is rather well done actually.

Where I got it wrong (if I did!) in my case is more during the installation of Debian on the SD card

66  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 22, 2011, 03:46:52 PM
Hi,

I use the SD reader on the side of the guruplug.

I think I am not too far just confused.

Here where I am at:

I have the ubout from the site I mentioned earlier. I installed on my SD card the latest Debian from this web site:
http://bzed.de/posts/2010/05/installing_debian_on_the_guruplug_server_plus/

I changed the printenv to boot from the card and I can see it load uImage and start
 
Code:
scanning bus for devices... 3 USB Device(s) found                               
       scanning bus for storage devices... Device NOT ready                     
   Request Sense returned 02 3A 00                                             
2 Storage Device(s) found                                                       
Loading file "/uImage" from usb device 1:1 (usbdb1)
 1431936 bytes read                                                             
## Booting kernel from Legacy Image at 06400000 ...                             
   Image Name:   Debian kernel                                                 
   Image Type:   ARM Linux Kernel Image (uncompressed)                         
   Data Size:    1431872 Bytes = 1.4 MiB                                       
   Load Address: 00008000                                                       
   Entry Point:  00008000                                                       
   Verifying Checksum ... OK                                                   
   Loading Kernel Image ... OK                                                 
OK                                           

and then it stops at

Code:
Uncompressing Linux... done, booting the kernel.


also before it used to go further than that but ended in a Kernel Panic. Don't know why it stops there now Sad
Told you I am confused!

So I think that the SD card is recognized but somehow I must be missing something.

I will redo once more the Debian Installation in case
67  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 22, 2011, 11:38:49 AM
Actually I would like to rebound on this

I advised the link above and it works great for updating the uboot but over the last few days I have been
trying to finally get my plug to boot form an 8G microSD I have and I just don't get anywhere.

I reach a point where I am totally confused and don't know what to do anymore so for sure some extra doc for dummy like
me would be great

It is really a shame that Marvell and Globalscale are not more proactive in terms of documentation or updating software


68  Hardware and U-Boot firmware / U-Boot stuff / Re: One good uniform way to install a guru/sheeva wanted on: February 20, 2011, 07:26:05 AM
This is the best site I found to update your guruplug

http://oinkzwurgl.org/guruplug
69  General Category / Application ideas and development Q/A / Re: GlobalScale, you have some MAJOR explaining to do. on: January 15, 2011, 08:45:58 AM
I was going to reply but Bluto was faster

I would add that what makes the internet as you say is the file called /etc/resolv.conf.

Now at worst what could happen here is that if Ubuntu changes the ip address of ports.ubuntu.com then you will
loose connectivity with it as your system will still use the IP address in the hosts

Not smart but definitely no evil here
70  General Category / General Discussion / Re: Captive portal on guruplug on: December 25, 2010, 07:23:42 AM
merci pour le lien....c'est vrai que j'ai ete un peu faineant sur ce coup

71  General Category / General Discussion / Re: Captive portal on guruplug on: December 23, 2010, 08:01:40 AM
probably a stupid question but....what is a captive portal?
72  Linux Stuff / General Linux questions / Re: GuruPlug: Change address range now cant log in on: December 02, 2010, 07:57:36 AM
may be you changed the ip of the guruplug as well by mistake

I assume you connect to the wifi point of the guruplug? and not from another wifi?

if so you could try to renew the ip address and see what ip si actually giving you the renewal....that should be the guruplug access point

as root

dhclient <interface of your laptop>
73  General Category / General Discussion / Re: Zoneminder 1.24.2 working in Guruplug server+!!! on: October 18, 2010, 01:16:14 PM
hello

Could you please describe your step to get it to work?

74  General Category / General Discussion / Re: Tonido vs Amahi vs Plugbox on: October 02, 2010, 05:11:20 PM
Hello,

What application do you think you will need?

I am testing Amahi (on a Guruplug) at the moment and not all applications are working correctly.

See that page:
http://wiki.amahi.org/index.php/Amahi_Plug_Edition

and for the apps that works for sure:

http://wiki.amahi.org/index.php/SP_Apps

Amahi is a nice product. I never tried Tonidoplug so can't say if it is better or not but at you say the Ubunutu no longer support ARM
75  Linux Stuff / General Linux questions / Re: uaputl sources: where? on: September 27, 2010, 07:27:56 PM
hello flipflip

Would you mind telling us how to compile it?

I would like to try it on the amahi plug I have to see if it would work in Fedora as well

Thanks
Pages: 1 ... 3 4 [5] 6 7 ... 9