• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: 1 2 [3] 4 5 ... 9
31  Hardware and U-Boot firmware / U-Boot stuff / Wrong Image Format for bootm command on: April 22, 2011, 06:28:41 PM
Hi,

My guruplug was working perfectly well but tonight I decided to reboot it and got the following :
Code:
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0, egiga1
88E1121 Initialized on egiga0
88E1121 Initialized on egiga1
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
       scanning bus for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
Device NOT ready
   Request Sense returned 02 3A 00
3 Storage Device(s) found
Loading file "/uImage" from usb device 2:1 (usbdc1)
1433640 bytes read
Loading file "/uInitrd" from usb device 2:1 (usbdc1)
5678260 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
GuruPlug>>

This plug is booting entirely off a USB drive and I must say I was able to reboot it several time in the past and it worked

Tonight tough it won't. I have extracted the USB and did an fsck on it and all is good.

What image format is it complaining about?

Does anyone know what it can be?

Here is my printenv but it hasn't change in weeks

Code:
GuruPlug>> printenv
baudrate=115200
bootargs=console=ttyS0,115200 root=/dev/sdc2 rootdelay=10
bootcmd=run x_bootcmd
bootdelay=3
eth1addr=00:50:43:01:83:91
ethact=egiga0
ethaddr=00:50:43:01:83:90
filesize=56A4B4
stderr=serial
stdin=serial
stdout=serial
x_bootargs=console=ttyS0,115200
x_bootargs_root=root=/dev/sdc2 rootdelay=10
x_bootcmd=${x_bootcmd_usb}; ${x_bootcmd_uImage}; ${x_bootcmd_uInitrd}; setenv bootargs ${x_bootargs} ${x_bootargs_root};bootm 0x6400000 0x1100000;
x_bootcmd_uImage=ext2load usb 2:1 0x0640000 /uImage
x_bootcmd_uInitrd=ext2load usb 2:1 0x1100000 /uInitrd
x_bootcmd_usb=usb start

I will try to reboot on the internal nand
32  Linux Stuff / General Linux questions / Re: Crash message in dmesg on: April 19, 2011, 03:41:09 AM
wow

you can say that from that message?

I am going to remove my jtag and see what happens

The stange thing is that the JTAG has alway been connected but it only started recently

Also aprt from these message nothing seems to happen. The plug doesn't reboot

Thnaks
33  Linux Stuff / General Linux questions / Crash message in dmesg on: April 18, 2011, 06:04:56 PM
For the last few days I see the following messages.

I have searched google but haven't found anything very helpfull

Is it bad?

Code:
[508735.142688] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
[508742.503804] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
[508746.500890] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
[1154195.192489] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
[1154201.204403] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
[1154205.214692] SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) saK show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
34  Hardware and U-Boot firmware / Hardware / Re: A Kick-Butt Replacement Power Supply on: April 17, 2011, 06:55:32 PM
When you say you send it to fab. DO you mean that you use an company to create the PCB?

Do you have recommendation? what is the cost for that card ?

I am connecting so many things to my guruplug that it might be usefull to start thinking about a better power

35  Hardware and U-Boot firmware / Hardware / Re: Is this a Sympton of a dying SD-Card? on: April 07, 2011, 04:42:31 AM
birdman: I had the same question about big file system. My disk at home is 250Gib Sad so hope it will not happen

The only thing I can think of is that SD are not Harddisk and might be treated differently by fsck but then agaain it is my hope !
36  Hardware and U-Boot firmware / U-Boot stuff / Re: Choosing uboot/uImage for Guru Server on: April 07, 2011, 04:38:31 AM
I had the same issue crunch until I realise that the kwb file works

Like you not sure what the difference is or when you use the bin rather than the kwb!

may be pingtoo knows Wink
37  General Category / General Discussion / Re: Who wants a guruplug plus? on: April 06, 2011, 07:25:51 AM
damn it you beat me Smiley
38  Hardware and U-Boot firmware / Hardware / Re: Is this a Sympton of a dying SD-Card? on: April 06, 2011, 07:24:41 AM
4G should be enough to fix a 2G file system. may be something I have not thought about yet.

the file system of the SD card is about 6 Gig so it could be an issue
39  Hardware and U-Boot firmware / Hardware / Re: Is this a Sympton of a dying SD-Card? on: April 05, 2011, 07:31:36 PM
pingtoo

My swap is about 4 Gig

I can actually see the real RAM (2Gig) disappearing as the fsck goes and then the PC slows down until it fails

You think 2Gig (RAM) + 4 Gig swap is not enough?

I don't see that behaviour with real harddisk when I check them. Does it have to do with the fact that SD card are different the harddisk?

I will try to add a spare partition to increase the swap.

thanks for the tip.
40  Hardware and U-Boot firmware / Hardware / Re: Is this a Sympton of a dying SD-Card? on: April 05, 2011, 09:21:02 AM
strangely enough I had a similar issue with my SD card. It has been up and running for about a month but yesterday morning when I connected I noticed that my SIP client was down!

Looking into it more the all system was complaining that the / partition was in read only mode

I extracted it from the plug to do a fsck on it but fsck failed because of "memory allocation failure" !

So basically I can't fix my SD and I have now reinstall the system on a USB key I have using ext2 only rather than ext4

What file system do you use?
41  Linux Stuff / Kernel / Re: 2.6.35.12 new kernel available on: April 04, 2011, 10:50:42 AM
Thanks a lot

I will have a go on my test usb stick
42  Linux Stuff / Kernel / Re: 2.6.35.12 new kernel available on: March 31, 2011, 09:31:46 PM
Hello,

Thanks a lot for providing these kernel

I have one question : is there a way to have these kernel burned to an SD card rather than on the nand?

and sorry for my ignorance but what is the difference between nandkernel and rootkernel?

Looking at the script...is this actually by using the option "rootkernel" that I could burn it to a different place than the nand?
43  Hardware and U-Boot firmware / U-Boot stuff / Re: Choosing uboot/uImage for Guru Server on: March 24, 2011, 04:07:25 AM
as pingtoo says we need to start from scratch.

When this happened to me ( and the hard reset didn't help!) I ended reflashing the all plug with the uboot, uImage and kernel from the
globalscale page as they are known to work...

Then I updated the uboot (the one from flip-flip) and I installed the latest debian.

44  Hardware and U-Boot firmware / U-Boot stuff / Re: Choosing uboot/uImage for Guru Server on: March 23, 2011, 04:04:10 PM
sorry to repeat myself but have you try to remove the power from the plug and plug it again?
45  Hardware and U-Boot firmware / U-Boot stuff / Re: Choosing uboot/uImage for Guru Server on: March 21, 2011, 01:39:54 PM
Also for some reason unexplained to me sometime the plug will just not pass booting the kernel until you unplugged from the wall and plug it back

this is my experience and I know other have had the same issue.
Pages: 1 2 [3] 4 5 ... 9