• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: [1]
1  Hardware and U-Boot firmware / Hardware / Re: Anyone preorder d2plug? on: September 22, 2011, 11:04:27 AM
They have not even updated the website saying the product is being shipped also!
2  Hardware and U-Boot firmware / Hardware / Re: Anyone preorder d2plug? on: September 22, 2011, 08:52:22 AM
Actually I see some downloads here: http://www.plugcomputer.org/downloads/d2plug/
3  Hardware and U-Boot firmware / Hardware / Re: Anyone preorder d2plug? on: September 22, 2011, 08:23:52 AM
Now I want to be able to see the downloads for this device!
4  Hardware and U-Boot firmware / Hardware / Re: Anyone preorder d2plug? on: September 20, 2011, 12:07:15 PM
Mine got shipped today! Its about time!
5  Hardware and U-Boot firmware / Hardware / Anyone preorder d2plug? on: July 07, 2011, 05:23:21 AM
I preordered it in the beginning of June, and very disappointed that it has been delayed until end of July.

Anyway, anyone know if it can run vanilla debian, or what kind of wireless chipset is inside?
6  Hardware and U-Boot firmware / U-Boot stuff / Re: Dreamplug/openocd on: June 15, 2011, 06:50:23 PM
At this time, openocd does not have support for the dreamplug's SPI/NOR so it cannot be done. however you can use openocd to halt the dreamplug, transfer your uboot into memory, resume and flash with existing command.

Warning, do not flash just any u-boot code you got. your u-boot code need to be able to boot from SPI so use "mkimage -l -u-boot-filename" to check it is bootable from SPI.

Good luck Smiley

Really? How would I start to do this? Any examples? This sounds like a way to recover if needed.
7  Hardware and U-Boot firmware / U-Boot stuff / Re: Dreamplug/openocd on: June 14, 2011, 04:38:33 PM
Is openocd going to have support for this spi/nor soon you think, is it in progress?
8  Hardware and U-Boot firmware / Hardware / Re: Flash Uboot on Bricked Dreamplug? on: April 19, 2011, 09:27:36 PM
Does openocd have any access to the internal NAND, or just the sdcard (sorry, not really sure what SPI is)
9  Hardware and U-Boot firmware / Hardware / Flash Uboot on Bricked Dreamplug? on: April 17, 2011, 12:45:34 PM
Ok, I have not bricked my dreamplug yet, but I want to be able to reflash uboot before I start messing around with it (I am notorious for bricking things, and I LOVE writing zeros to the nand). Has anyone got Openocd working? I am looking at the runme.sh script from the guruplug, which is what I used for the guruplug, and it seems it requires some hardware specific config files. I notice http://code.google.com/p/dreamplug/downloads/detail?name=dream_burn_spi.tar.bz2, but this seems to be some dump of someones home directory or something.
10  Hardware and U-Boot firmware / Hardware / Re: I just received a new Dreamplug today on: March 29, 2011, 08:11:26 PM
I just received a new Dreamplug today and it doesn't match the DreamPlug user guide.

root@ubuntu:/proc# cat cpuinfo
Processor       : Feroceon 88FR131 rev 1 (v5l)
BogoMIPS        : 396.49
Features        : swp half thumb fastmult edsp
CPU implementer : 0x56
CPU architecture: 5TE
CPU variant     : 0x2
CPU part        : 0x131
CPU revision    : 1

root@ubuntu:/proc# uname -a
Linux ubuntu 2.6.33.6 #1 PREEMPT Tue Feb 8 03:18:41 EST 2011 armv5tel GNU/Linux

root@ubuntu:/proc# cat version
Linux version 2.6.33.6 (root@localhost.localdomain) (gcc version 4.2.1) #1 PREEMPT Tue Feb 8 03:18:41 EST 2011


root@ubuntu:/etc# cat debian_version
5.0


U-Boot 2011.06-02334-g8f495d9-dirty (Mar 01 2011 - 06:57:05)
Marvell-DreamPlug

SoC:   Kirkwood 88F6281_A0
DRAM:  512 MiB
SF: Detected MX25L1606 with page size 256, total 1 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0, egiga1
88E1121 Initialized on egiga0
88E1121 Initialized on egiga1
Hit any key to stop autoboot:  0
Marvell>> ?
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
date    - get/set/reset date & time
dhcp    - boot image via network using DHCP/TFTP protocol
echo    - echo args to console
editenv - edit environment variable
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
go      - start application at address 'addr'
help    - print command description/usage
iminfo  - print header information for application image
imxtract- extract a part of a multi-image
itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mtest   - simple RAM read/write test
mw      - memory write (fill)
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
sleep   - delay execution for some time
source  - run script from memory
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version


Marvell>> printenv
bootcmd=setenv ethact egiga0; ${x_bootcmd_ethernet}; setenv ethact egiga1; ${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootc;
bootdelay=3
baudrate=115200
x_bootcmd_ethernet=ping 192.168.2.1
x_bootcmd_usb=usb start
x_bootcmd_kernel=fatload usb 0 0x6400000 uImage
x_bootargs=console=ttyS0,115200
x_bootargs_root=root=/dev/sda2 rootdelay=10
ethact=egiga0
eth1addr=XX:XX:XX:XX:XX:XX
ethaddr=XX:XX:XX:XX:XX:XX
stdin=serial
stdout=serial
stderr=serial

Environment size: 524/4092 bytes

Well, there you have it.

If someone wants me to print out anything more, I'd be happy to.

One other observation and that is that this system feels really doggy.  Like the 396 BogoMips is a realistic number.  My GplugD shows 796 BogoMips and feels slower than my GuruPlug that shows 1196 BogoMips.  If anyone has any ideas about what it all means I'd love to hear about it.

I'd also like to get this over on Debian so if anyone has any experience doing that perhaps you could point me in the right direction.  Every other Plug I have came with Debian.

Ubuntu 9.04 is not what I want to be running.

Thanks!


Same exact issue for me, I have ubuntu, and same MIPS.  Did they have you file an RMA, or did they just send you a new one, because they are making me file an RMA (but are paying for a shipping label).
11  Hardware and U-Boot firmware / Hardware / Re: I just got my Dreamplug on: February 12, 2011, 08:35:17 PM
They started shipping the dream plugs, or are you just one of those special people that get it before the rest of us? Unfortunately, I am not aware of a way getting serial/jtag functionality without the jtag box.
12  General Category / General Discussion / Guruplug shipping! on: April 30, 2010, 03:10:49 PM
I sent an email out about the guruplugs, they are now shipping, mine will be shipped in a couple of days! Anybody get theirs yet?
Pages: [1]