• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: [1] 2
1  General Category / General Discussion / Re: MPD issues on the Guru on: August 18, 2010, 03:49:28 PM
@xxcn

I had the same problems as you. having just "type" and "name" solved my problems. in your case try


audio_output {
        type                    "alsa"
        name                    "USB Audio"
#        device                  "hw:1,0"
#        format                  "44100:16:2"
#        use_mmap            "yes"
}

or something like that so you get only "type" and "name"
2  General Category / General Discussion / Re: SheevaPlug Installer with updated kernel, uboot, distro ? on: January 12, 2010, 01:18:07 PM
Holly sh..  Grin Grin Grin Grin Grin Grin Grin Grin Grin

orion_nand instead of orion_mtd solved all problems, I got my Debian now, thank you guys, especially pingtoo for spending so much time solving this problem.
3  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 03:59:07 PM
Sorry for the confusion, I tried the whole installation again with ubi0, so right now I have ubi0 as you see below

Code:
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
mtdpartitions=mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)
ethaddr=00:50:43:01:69:8B
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootargs_console=console=ttyS0,115200
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
arcNumber=2097
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
bootargs=console=ttyS0,115200 mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
filesize=32D62A

Environment size: 2192/131068 bytes
Marvell>>

When running recover3 again I get

Code:
Marvell>> run recover3
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
reading uImage
...

2620504 bytes read
reading initrd
...

3331626 bytes read

NAND erase: device 0 offset 0x100000, size 0x400000
Erasing at 0x4e0000 -- 100% complete. Cleanmarker written at 0x4e0000.
OK

NAND write: device 0 offset 0x100000, size 0x400000

Writing data at 0x4ff800 -- 100% complete.
 4194304 bytes written: OK
Marvell>>

 when I restart it then I get the following
Code:
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 980 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Kirkwood: Gating clock using mask 0x1ac224
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4012, nTxLock = 32100
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:69:8b
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3673 at 0x00001cb20000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "uImage"
UBI: MTD device size:            4 MiB
UBI: number of good PEBs:        32
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 32
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 48/23
UBI: background thread "ubi_bgt0d" started, PID 446
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2034-03-09 13:32:58 UTC (2025523978)
UBIFS error (pid 1): ubifs_recover_master_node: failed to recover master node
List of all partitions:
1f00            1024 mtdblock0 (driver?)
1f01            4096 mtdblock1 (driver?)
1f02          519168 mtdblock2 (driver?)
No filesystem could mount root, tried:  ubifs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c00309c0>] (unwind_backtrace+0x0/0xe0) from [<c003db50>] (panic+0x50/0x120)
[<c003db50>] (panic+0x50/0x120) from [<c0008ec0>] (mount_block_root+0x1d4/0x214)
[<c0008ec0>] (mount_block_root+0x1d4/0x214) from [<c000908c>] (prepare_namespace+0x90/0x1c4)
[<c000908c>] (prepare_namespace+0x90/0x1c4) from [<c0008734>] (kernel_init+0xc0/0xec)
[<c0008734>] (kernel_init+0xc0/0xec) from [<c0040b3c>] (do_exit+0x0/0x6ac)

 Undecided
4  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 02:03:26 PM
zour commands give me the following

Code:
Marvell>> nand read.e 0x02000000 0x00100000 0x00400000

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
Marvell>> imi 0x02000000

## Checking Image at 02000000 ...
   Bad Magic Number
Marvell>> imi 0x00800000

## Checking Image at 00800000 ...
   Bad Magic Number
Marvell>> cmp.b 0x02000000 0x00800000 0x400000
Total of 4194304 bytes were the same
Marvell>>


I did try to change bootargs_root=... root=ubi... but it didnt help, so I changed it again, and the last run was with 0, I have checked my files, or just look the post where I have attached some files instead of doing printenv, it already contains ubi0
5  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 11:36:40 AM
 Grin

I thought uboot env thats a directory in my installer  Grin

Code:
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs_root=ubi.mtd=1 root=ubi2:rootfs rootfstype=ubifs
mtdpartitions=mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)
ethaddr=00:50:43:01:69:8B
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootargs_console=console=ttyS0,115200
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
arcNumber=2097
filesize=32D62A
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
bootargs=console=ttyS0,115200 mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi2:rootfs rootfstype=ubifs

Environment size: 2192/131068 bytes
Marvell>>

6  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 10:43:59 AM
hi

 Sad

I hope these are the files you are looking for.

u-boot-dflt

Code:
baudrate 115200

loads_echo 0

ipaddr 10.4.50.165

serverip 10.4.50.5

rootpath /mnt/ARM_FS/

netmask 255.255.255.0

stdin serial

stdout serial

stderr serial

console console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root)

mainlineLinux no

CASset min

enaMonExt no

enaCpuStream no

enaWrAllo no

pexMode RC

disL2Cache no

setL2CacheWT yes

disL2Prefetch yes

enaICPref yes

enaDCPref yes

sata_dma_mode yes

MALLOC_len 1

ethprime egiga0

netbsd_en no

vxworks_en no

bootargs_root root=/dev/nfs rw

bootargs_end :::DB88FXX81:eth0:none

image_name uImage

bootcmd tftpboot 0x2000000 $(image_name);setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig);  bootm 0x2000000;

standalone fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;

bootdelay 3

disaMvPnp no

ethaddr 00:50:43:01:69:8B

ethmtu 1500

mvPhoneConfig mv_phone_config=dev0:fxs,dev1:fxs

mvNetConfig mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500

usb0Mode host

yuk_ethaddr 00:00:00:EE:51:81

nandEcc 1bit

netretry no

rcvrip 169.254.100.100

loadaddr 0x02000000

autoload no

enaAutoRecovery yes

ethact egiga0

uboot-nand-custom

Code:
#### Change ONLY in the following few lines

# Following for installation on SD card. If you want to boot from USB stick change it to /dev/sda1
# or /dev/mtdblock1 if you installed rootfs on the NAND inside the plug
bootargs_root ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs

# NAND flash partitions. If using kernel >= 2.6.30 then replace orion_nand with orion_mtd
mtdpartitions mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)

# The following is an example MAC address. Change it according the MAC on the back side of the plug
ethaddr 00:50:43:01:69:8B

#### DONT change the following.
# Automated process the sets arcNumer to 2097, reset, runs uImage and initrd from USB stick and set bootcmd to 'real_bootcmd' above
# Bootcmd to be used after all installation is done
real_bootcmd setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootargs_console console=ttyS0,115200
bootcmd run recover1
recover1 setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2 run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3 run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4 usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
7  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 08:29:14 AM
Hez again,

Ok, the first part did work and it saw like the OS is got installed to a big partition, but I dont know exactly and at the end I saw a reboot failure as you expected, so i did reboot -f
during the reboot I forgot to stop the boot and I got following at the end

Code:
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2034-03-09 06:08:17 UTC (2025497297)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi2:rootfs", error -19
VFS: Cannot open root device "ubi2:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00            1024 mtdblock0 (driver?)
1f01            4096 mtdblock1 (driver?)
1f02          519168 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c00309c0>] (unwind_backtrace+0x0/0xe0) from [<c003db50>] (panic+0x50/0x120)
[<c003db50>] (panic+0x50/0x120) from [<c0008ec0>] (mount_block_root+0x1d4/0x214)
[<c0008ec0>] (mount_block_root+0x1d4/0x214) from [<c000908c>] (prepare_namespace+0x90/0x1c4)
[<c000908c>] (prepare_namespace+0x90/0x1c4) from [<c0008734>] (kernel_init+0xc0/0xec)
[<c0008734>] (kernel_init+0xc0/0xec) from [<c0040b3c>] (do_exit+0x0/0x6ac)

then I rebooted with a little button on a sheevaplug and interrupted the reboot as you described, and I typed
Code:
Marvell>> setenv bootcmd ${real_bootcmd}
Marvell>> saveenv
Marvell>> boot

and I got the following output (second part is after reboot)

Code:
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd ${real_bootcmd}
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
Marvell>> boot

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

Is the booting image at 00800000?

now I will post the whole output. as I saw it during the last steps*the outputs above are extracted from this one
Code:
Bad eraseblock 3673 at 0x00001cb20000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "uImage"
UBI: MTD device size:            4 MiB
UBI: number of good PEBs:        32
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 32
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 45/22
UBI: background thread "ubi_bgt0d" started, PID 446
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2034-03-09 06:08:17 UTC (2025497297)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi2:rootfs", error -19
VFS: Cannot open root device "ubi2:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00            1024 mtdblock0 (driver?)
1f01            4096 mtdblock1 (driver?)
1f02          519168 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c00309c0>] (unwind_backtrace+0x0/0xe0) from [<c003db50>] (panic+0x50/0x120)
[<c003db50>] (panic+0x50/0x120) from [<c0008ec0>] (mount_block_root+0x1d4/0x214)
[<c0008ec0>] (mount_block_root+0x1d4/0x214) from [<c000908c>] (prepare_namespace+0x90/0x1c4)
[<c000908c>] (prepare_namespace+0x90/0x1c4) from [<c0008734>] (kernel_init+0xc0/0xec)
[<c0008734>] (kernel_init+0xc0/0xec) from [<c0040b3c>] (do_exit+0x0/0x6ac)
�
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Dec 27 2009 - 22:03:21) Marvell version: 3.4.27

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFEE0

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd ${real_bootcmd}
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
Marvell>> boot

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>
8  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 10, 2010, 05:48:55 AM
Hey, sorry I needed some sleep yesterday  Smiley

Yes you are right about what I am currently have, and I already tried to run the installer many times, the output is always the same. Now I tried your commands and I got this

Code:
Memory: 256MB 256MB = 512MB total
Memory: 510080KB available (4728K code, 998K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 980 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Kirkwood: Gating clock using mask 0x1ac224
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 3252K
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4012, nTxLock = 32100
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:69:8b
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3673 at 0x00001cb20000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2034-03-09 03:34:43 UTC (2025488083)
RAMDISK: gzip image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 140K
usb 1-1: new high speed USB device using orion-ehci and address 2
/bin/sh: can't access tty; job control turned off
# usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
scsi 0:0:0:0: Direct-Access     USB      DISK 2.0         1219 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3915776 512-byte hardware sectors: (2.00 GB/1.86 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk

# cat /proc/mtd
cat: can't open '/proc/mtd': No such file or directory
# mount -t proc proc /proc
# mount -t sysfs sys /sys
# mdev -s
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00400000 00020000 "uImage"
mtd2: 1fb00000 00020000 "root"
#
9  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 04:35:37 PM
I mean my sheevaplug used to work with a preinstalled ubuntu. It had some bugs like described on the wiki pages, thats all. Then I wanted to install new OS with a new kernel without bugs etc. so I am here, so your first assumption was correct Smiley

You asked me for a kernel log by typing "boot", here it is:

Code:
Marvell>> boot

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> version

U-Boot 1.1.4 (Dec 27 2009 - 22:03:21) Marvell version: 3.4.27 - pingtoo patch.01
Marvell>>
As you can see above, I use your uboot.
10  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 02:46:21 PM
I am on 3.4.27 now, I know the log below is different.
Uboot delivered with the installer has a little bit different size and its not working too. I use an usb stick and its ofcourse working with this device (Kernel is loaded). When I used the factory defaults I could mount and access my usb device via ssh. And as you see the kernel is being loaded. When i got my sheevaplug I did run distro update, but ofcourse it didnt work but i had a still working sheevaplug (ssh access) but some dependencies were broken. But I cant imagine it has something todo with my current errors, since everything got deleted. I guess some parameter is wrong (installer).

What do you mean by "sheeva-instalation"? I am trying it all the time and evertime I get the same error: no space left on device because it writes in wrong partition.
11  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 01:27:48 PM
Hey,

I have tried your version of uboot and its the same. I guess i already used it before cos the size was the same.

Code:
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> boot   

NAND read: device 0 offset 0x100000, size 0x400000

Reading data from 0x4ff800 -- 100% complete.
 4194304 bytes read: OK
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

12  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 12:01:06 PM
Hi, thank you for help.

I have attached printenv, but I dont know how to get kernel messages, on my desktop mashine I would try /var/log but I am lost with sheeva  Undecided

Code:
Marvell>> printenv | more
## Error: "|" not defined
## Error: "more" not defined
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=a0000
e=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs_root=ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs
mtdpartitions=mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)
ethaddr=00:50:43:01:69:8B
real_bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
bootargs_console=console=ttyS0,115200
recover1=setenv mainlineLinux yes; setenv arcNumber 2097; setenv bootcmd run recover2; saveenv; reset
recover2=run recover3; setenv bootcmd $(real_bootcmd); saveenv; setenv bootargs $(bootargs_console) $(mtdpartitions) root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
recover3=run recover4; nand erase clean 0x00100000 0x00400000; nand write.e 0x00800000 0x00100000 0x00400000
recover4=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
arcNumber=2097
filesize=32D62A
bootcmd=setenv bootargs $(bootargs_console) $(mtdpartitions) $(bootargs_root); nand read.e 0x00800000 0x00100000 0x00400000; bootm 0x00800000
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=a0000
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
bootargs=console=ttyS0,115200 mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs

Environment size: 2210/131068 bytes
Marvell>>
13  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 10:25:37 AM
No, I used a 2.6.32-3 kernel. Right now I tried  with the one delivered with the installer and I get the same error.  Undecided
14  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 09:27:19 AM
Ok I have attached the files.

Host.txt is the screen where i start the installation. And 2 screenshots is what I recieve from sheevabox. I hope its enough information.
15  General Category / General Discussion / Re: Sheevaplug installer - version 1.0 on: January 09, 2010, 07:51:14 AM
Hey guys, i need some help.

I use the Installer 1.0 to install the os on a Flash drive. During the installation I see a message that there is not enough free storage and when it restarts a see: bad magic number. During the installation it seems to write to a 4mb partition.
Here is my uboot-nand-custom.txt:

Code:
# Following for installation on SD card. If you want to boot from USB stick change it to /dev/sda1
# or /dev/mtdblock1 if you installed rootfs on the NAND inside the plug
bootargs_root ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs

# NAND flash partitions. If using kernel >= 2.6.30 then replace orion_nand with orion_mtd
mtdpartitions mtdparts=orion_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)

Probably i have to change here something, but I dont know what to change. And I dont understand what i have to change to /dev/mtdblock1 . I tried to change ubi-mtd=1 to 0 and root=ubi0 to 1 but it didnt help. And suggestions?
Thanks
Pages: [1] 2