• Home
  • Help
  • Search
  • Login
  • Register
  Show Posts
Pages: [1]
1  Linux Stuff / Kernel / Re: 3.2 new kernel available on: January 23, 2012, 07:54:58 AM
My Sheevaplug is still stopping after loading the 3.2.1 kernel. I am about to try the 3.1.9.

Code:
U-Boot 2011.12 (Jan 08 2012 - 21:53:47)
Marvell-Sheevaplug - eSATA - SD/MMC

SoC:   Kirkwood 88F6281_A1
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
Marvell>> usbstart
Unknown command 'usbstart' - try 'help'
Marvell>> usb start
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Marvell>> fatload usb 0:1 0x00800000 /sheeva-3.2.1-uImage
reading /sheeva-3.2.1-uImage

2918568 bytes read
Marvell>> fatload usb 0:1 0x01100000 /uInitrd
reading /uInitrd

4305500 bytes read
Marvell>> setenv bootargs console=ttyS0,115200n8 base-installer/initramfs-tools/driver-policy=most
Marvell>> bootm 0x00800000 0x01100000
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.2.1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2918504 Bytes = 2.8 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   debian-installer ramdisk
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4305436 Bytes = 4.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Marvell>> ls
mtdids not defined, no default present
Marvell>> usb start
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Marvell>> printenv
arcNumber=2097
baudrate=115200
bootargs=console=ttyS0,115200 rootdelay=10
bootargs_console=console=ttyS0,115200
bootargs_root= root_delay=10
bootcmd=setenv bootargs $(bootargs_console) rootdelay=10; run bootcmd_mmc; bootm 0x00800000 0x01100000
bootcmd_mmc=mmc init; ext2load mmc 0:1 0x00800000 /uImage; ext2load mmc 0:1 0x01100000 /uInitrd
bootdelay=3
ethact=egiga0
ethaddr=F0:AD:4E:00:D9:35
filesize=2C88A8
mainlineLinux=yes
stderr=serial
stdin=serial
stdout=serial
x_bootargs=console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),4m@1m(kernel),507m@5m(rootfs) rw
x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
x_bootcmd_kernel=nand read 0x6400000 0x100000 0x400000
x_bootcmd_sata=ide reset;
x_bootcmd_usb=usb start;
Pages: [1]